Red Dot Sight, Manufacturer : C-More (USA), Model : RTS2B V5, Dot Size : 6 MOA, Color : Black
RTS2 is a proven collimator with many victories in IPSC world championships, USPSA championships and many other national, local and international competitions.
With a large 25.75mm x 22mm display, it provides a distortion-free image at any distance from the eye and fast target acquisition, while thin frames provides a wide field of view.
Applied hard-coated glass lens provides maximum scratch resistance and light transmission, while the parallax-free design allows for aiming without the need to center the point.
Aircraft alloy (6061T6 aluminum) housing and reinforced electronics are designed to withstand the shooting of large caliber firearms.
The V5 mark on this model means new, reliable electronic system. In addition, the new electronics feature the MSS motion detection system, which shuts down the device if no motion or vibration is detected within 3 minutes. Dot turns on as soon as motion or vibration is detected in the mode in which it was set before shutting down. This system provides much longer operating time on a single battery.
On the left side of the device there are 2 buttons - up and down, with which the shooter can precisely adjust the intensity of the dot depending on the lighting conditions. The user can choose from 10 modes of dot intensity.
This collimator is zeroed vertically with a screw on the top and horizontally with a screw on the right side. 1 click matches 1 minute angle (1 MOA), which is the shift of the aiming point by 2.91 cm at a distance of 100 m.
A CR2032 lithium battery, located on the right side, is responsible for powering the collimator. This allows for easy replacement of the battery without the need to disassemble the sight and re-zero it. In addition, the place where the battery is located is sealed with an o-ring, which ensures water resistance.
The set includes a collimator, glass protective cover, vertical and horizontal adjustment wrench, manual in English, mounting wrench and screws.
ASSEMBLY
The assembly requires a mounting plate for the specific weapon model. There is a list of compatible guns below with a link to the mounting :
- Beretta 92 without a cutout for a sight, after the earlier rear sight disassembly + Installation Manual - CLICK HERE
- Glock 17/19/22/23/25/26/27/28/31/32/33/34/45 without a cutout for a sight, after the earlier rear sight disassembly + Installation Manual - CLICK HERE
- Bul Axe Cleaver / Hatchet without a cutout for a sight, after the earlier rear sight disassembly + Installation Manual - CLICK HERE
- Colt 1911 without a cutout for a sight, after the earlier rear sight disassembly + Installation Manual - CLICK HERE
- Ruger Mk II, III, IV i 22/45without a cutout for a sight, after the earlier rear sight disassembly + Installation Manual - CLICK HERE
- HK VP9/SFP9 with a slot for a sight - CLICK HERE
- Canik TP9 SFx / Elite Combat with a slot for a sight - CLICK HERE
- Glocks in (MOS) Version - with a slot for a sight - CLICK HERE
- Picatinny rail adapter - CLICK HERE
- 3/8" rail adapter - CLICK HERE
- Distance - Additional 2.75mm elevation for the sight - CLICK HERE
AVAILABLE IN 4 VERSIONS
Smaller dots work better for precision shooting, while the more MOA a dot has, the easier it is to place the aiming point on the target at closer distances. In addition, larger dots perform better in brighter areas.
THE FOLLOWING ILLUSTRATION SHOWS THE COVERAGE OF THE TARGET WITH DIFFERENT SIZE MOA AT A DISTANCE OF 50 YARDS
Dot size is specified in minute angles ("MOA"), where 1 MOA matches 1 inch at a distance of 100 yards. For example, a 2 MOA module will cover an area of 2 inches at a distance of 100 yards, a 6 MOA module will cover an area of 6 inches, and so on. Reducing the distance from the target by half also reduces the coverage by half - a 2 MOA module will cover an area of 1 inch at a distance of 50 yards, a 6 MOA module will cover an area of 3 inches, and so on.
TABLE OF TARGET COVERAGE AT DIFFERENT DISTANCES
Out of stock
(0 pcs.)
